Validation floor
Your whole floor, one screen
Rigs connected
0/ 8
1 device updating
Active faults
0
CHAMBER-02
Tests completed today
0
▲ 3 vs yesterday
Avg detection time
2m 14s
▼ 38s improvement
Idle hours saved
0hrs this month
▲ 22% vs last month
Activity feed
View all
Sentinel
Alerts & Rules
Active incidents, alert history, and user-defined detection rules across your floor.
Active Incidents
Alert History
Rules Engine
Channels
CriticalSoak aborted · thermal runaway detected
webhook ✓email ✓×2 repeats
WarningCell voltage approaching lower bound (3.21V)
webhook ✓email ✗ timeout
Correlated timeline
Every signal, one clock
Scrub across screen captures, OCR events, telemetry, and bus traffic, all correlated to a single master timeline.
CHAMBER-02 · 00:00 to 04:00 · AUG 25 2026
03:11:42
Screen events (OCR)
Sentinel alerts
Temperature (°C)
Observations
Screen at 03:11:42
SCREEN CAPTURE PREVIEW
OCR: "ERROR: Thermal runaway detected. Soak aborted at cycle 14 of 50. Chamber temp: 91.4°C. DUT surface: 88.2°C."
Context at 03:11:42
DUT Config
Firmware v2.3.1 · Pack B · Cell count: 14S · BMS rev 4.1
Rig State
Chamber setpoint: 45°C · Ramp rate: 2°C/min · Cycle: 14/50
Last known good
Cycle 13 completed at 02:54 · All cells within spec
Observations
Loom for hardware testing
One-click captures with voice notes, auto-attached telemetry, and shareable permalinks. Share a moment of doubt in seconds.
SCREEN CAPTURE · CYCLER-050:14🎙 Voice note
Cell voltage sag on CYCLER-05 · hour 41 of 500h soak
SCREEN CAPTURE · HIL-030:08
Watchdog timeout during CAN bus regression · sequence hung at step 47
SCREEN CAPTURE · EMC-010:22🎙 Voice note
Radiated emissions 2dB over pre-scan limit at 430MHz
SCREEN CAPTURE · DYNO-010:06
Motor torque ripple at 4200 RPM · golden run drift detected
SCREEN CAPTURE · VIBE-020:11🎙 Voice note
Resonance peak shifted from 320Hz to 340Hz after thermal cycling
SCREEN CAPTURE · BENCH-040:18
Power supply output noise · 50mV ripple on 3.3V rail under load
Data in
Two ways in. No silo left out.
Weave takes data two ways: Sidekick edge boxes that read any rig's screen with zero integration, and direct connectors to the systems you already run. One floor, one data layer.
Sidekick rigs
0
7 live · 1 updating
Integrations live
0
4 more available
Unified into
1data layer
screen + integration
Sidekick edge
SCREEN-READ · ZERO INTEGRATION
Reads the rig's own screen over HDMI. No driver, no API, no vendor cooperation. Air-gap friendly. Reaches the rigs integration cannot.
Sidekick fleet
8 devices · 7 live · 1 updating
Screens read today
chamber · cycler · HIL · dyno · EMC · bench · vibe
Operator observations
one-click captures + voice notes
Any rig with a screen. That is the point. No integration to wait on.
Integrations
MULTI-VENDOR · PULL FROM YOUR STACK
Connect the tools you already run so historical and structured data lands in the same place, next to what the Sidekicks see.
NI SystemLink
TDMS files + test limits
WATS
WATS test reports
CSV / folder watch
\\lab-nas\results · hourly
REST API
POST /ingest · token auth
LIMS (LabWare)
sample + result records
MES / Ignition
line + station events
InfluxDB / historian
time-series telemetry
Custom parser
bring your own format
One data layer. Whether a signal is screen-read by a Sidekick or pulled from an integration, it lands on the same timeline and feeds the same Atlas. That is what makes the learning compound.
Learn & analyse
Atlas, the floor's compounding memory
Every observation teaches Weave a reusable skill. Skills are inspectable files, not model weights. They carry across rigs and get better each time they run.
Skills learned
0
▲ 5 this month
Shared across rigs
0
learned once, reused everywhere
Applied this month
0runs
across 8 rigs
Avg confidence
94%
▲ 2 pts
Intelligence in artifacts, not weights. Open any skill to read the exact steps it runs, edit it, or switch it off. Nothing here is a black box. When a Sidekick learns a skill on one rig, every rig on your floor inherits it.
Analyse
Runs & ROI
Test run history, pass rates, and the hard numbers on time and effort your floor is saving.
Tests completed
0
▲ 12% vs last month
Pass rate
87%
▲ 4 points
Idle hours saved
0hrs
≈ $28,400 value
Faults caught early
0
Avg 2m 14s detection
Daily test volume
View details
Jul 26Aug 25
Pass rate by rig
Recent runs
View all 347 runs
| Rig | Test | Started | Duration | Status | Faults | Observation |
|---|---|---|---|---|---|---|
| CHAMBER-02 | 500h thermal soak · Pack B | Aug 24 22:00 | 5h 11m | Aborted | 1 | OBS-041 |
| HIL-03 | CAN bus regression v4.1 | Aug 25 01:20 | 1h 34m | Pass | 0 | · |
| CYCLER-05 | Cell capacity · 1C discharge | Aug 25 00:15 | 2h 48m | Warning | 0 | OBS-040 |
| DYNO-01 | Torque sweep 0 to 6000 RPM | Aug 24 18:00 | 45m | Pass | 0 | · |
| EMC-01 | RE pre-scan 30MHz to 1GHz | Aug 24 16:30 | 1h 12m | Warning | 0 | OBS-039 |
| VIBE-02 | Random vibration · Z axis | Aug 24 14:00 | 3h 20m | Pass | 0 | · |
| BENCH-04 | Power rail stability · 3.3V | Aug 24 12:00 | 55m | Pass | 0 | · |
| CHAMBER-07 | Humidity cycling 20 to 95% RH | Aug 24 09:00 | 8h 15m | Pass | 0 | · |
Fleet
Devices
Manage Sidekick edge boxes across your validation floor. Firmware, health, and rig assignments.
Settings
Configuration
General
Team & Access
Integrations
Data & Retention
Audit Log
Organisation
Your workspace identity and defaults.
Appearance
Theme and display preferences.